Hvac Contracting Services

Air Conditioning Installation

Every installation starts with a Manual J load calculation so your system is sized for your home’s actual square footage and duct condition, not a rough guess. The scope covers the outdoor condenser, indoor evaporator coil, refrigerant line set, and a post-install airflow and pressure check before the job closes.

Air Conditioning Repair

Symptoms like warm air, short cycling, or ice buildup each point to a different component: capacitor, evaporator coil, drain line, or blower motor. The diagnostic visit runs a refrigerant pressure check and electrical contactor test first, then provides a written repair scope so you know the cost before work starts.

Boiler Repair & Installation

From a leaking circulator pump to a failed heat exchanger, boiler faults follow a clear diagnostic path before any work is quoted. If replacement is warranted, the scope covers old-unit removal, new boiler installation, condensate pipe connection, and a full operational test, all in a single written estimate.

Ductless Mini-Split Systems

A ductless mini-split pairs an outdoor condenser with one or more wall-mounted air handlers, connected by a refrigerant line set, no ductwork required. Systems are available from cooling-only to heat pump models rated for year-round use, with SEER ratings typically ranging from 18 to 25 depending on configuration and zone count.

Emergency HVAC & Plumbing Service

A burning smell, blank thermostat, active water leak, or complete loss of heat each require same-visit diagnosis, not a next-morning callback. The visit identifies the failed component and provides a written repair scope with pricing before touching any part, with after-hours rates included in the estimate upfront.

Furnace Repair & Replacement

Short cycling, no heat, or an odd noise each point to a specific component: igniter, blower motor, control board, or heat exchanger. A full diagnostic is run before repair or replacement is recommended, using the unit’s age and repair cost relative to its remaining value as the decision framework.

Heat Pump Installation & Repair

A reversing valve fault, refrigerant loss, or short cycling each require component-level diagnosis before a repair is quoted. Full installation includes ductwork modification if needed, indoor and outdoor unit placement, wiring, and a final startup test confirming the system hits its specified output in both heating and cooling modes.

Heating System Installation

A new heating system installation covers old-equipment removal, furnace or heat pump placement, PVC vent pipe or direct-vent setup, gas or electrical connections, and a calibrated startup test. Denver’s elevation requires altitude-adjusted sizing, a unit rated at sea level will run less efficiently here without that correction built into the selection.

Heating System Repair

Short cycling, cold air from vents, or a furnace that won’t start each trace back to a specific component. The diagnostic visit tests the igniter, flame sensor, gas valve, and safety shutoff in sequence, then provides a written repair scope naming the part and labor. No guesswork, no parts replaced on speculation.

Indoor Air Quality Solutions

Stale air, dust buildup, and recurring odors each point to a different root cause: source control, ventilation shortfall, or a filtration gap. The air quality assessment covers humidity levels, HVAC filter condition, and duct airflow before a targeted solution is recommended, rather than a generic product.

Plumbing Repair Services

Leaking supply lines, running toilets, slow drains, and water heater drips each follow a diagnostic path before a fix is scoped. The diagnostic visit checks shut-off valves, supply line condition, and drain traps, then provides a written repair scope, useful in older Denver homes where galvanized pipe can complicate straightforward fixture swaps.

Radiant Heating Services

A hydronic radiant system circulates heated water through PEX tubing embedded in the floor, controlled by a manifold and thermostat zoning. New installations, remodel retrofits, and repairs to existing systems all start with a loop check and pressure test to confirm the scope before any work is scheduled.

Tankless Water Heater Services

Tankless water heater work covers installation, replacement, and annual descaling flushes to clear mineral scale. Denver’s hard water and high-altitude gas pressure both affect unit performance, so every installation includes a gas pressure test and a flow rate sizing check to confirm the unit matches the home’s peak demand.

Water Heater Repair & Installation

No hot water, rusty output, a popping noise, or a visible leak each point to a specific component: heating element, thermostat, anode rod, or T&P relief valve. The fault is diagnosed first, then repair or full replacement is recommended based on the tank’s age, sediment level, and the condition of the anode rod.